Roller Shades

Lebanon, IN Roller Shades

One tube, no clutter, honest about the edges

Call (317) 863-9966Get Free Quote
Quick Answer

This section covers what the product does well, where it struggles, and what it costs to own over time rather than just to buy. All three matter on a purchase you'll live with for years.

  • Service: Roller Shades for Lebanon homeowners
  • Service area: Lebanon, IN and surrounding areas
    • We book measures without much delay. What you can't compress is the fabrication window, which runs two to five weeks depending on the product and the finish. Painted shutter finishes sit at the longer end.
  • Insured and bonded
  • Serving Lebanon, IN since 2008
Roller Shades Services

Expert Roller Shades for Lebanon Homes

A roller shade wants a clean rectangular opening with depth behind the front edge, and in Lebanon that describes exactly 40.0 percent of the housing stock. The 1,349 units built here in the 1990s brought drywall returns with no applied casing, the 820 built in the 2010s repeated it, and the Fischer Homes plans going up now at Cedar Ridge give the most consistent mounting depth in the city. One tube, one fabric, nothing to dust between slats. On a house with 16 to 24 openings and a limited budget, rollers let you spend the money on the rooms people sit in and still cover everything else properly.

The light gap is the part most people aren't told about. Lutron publishes 3/4 inch per side on its Roller 20/64 system and a standard factory deduction of 1/16 inch per side, so an inside mounted roller shows daylight down both edges by design. It gets worse past 120 inches of height or a 4 to 1 height to width ratio. Roll direction matters too: a regular roll hangs the fabric off the back of the tube and sits closer to the glass, a reverse roll clears a deep sill on a pre-1940 opening but won't work behind a fascia. If you need darkness, ask us about side channels before you order.

When to Call

Signs You Need Roller Shades

If you notice any of these in your Lebanon home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

Hardwood floors have faded in a stripe by the window

New shades will not join the house automation system

The chain hangs loose with no tensioner fitted

One window needs a motor because nobody can reach it

You want to see out without being seen from outside

The bottom bar hangs crooked against the sill line

Existing shades have gone brittle and yellow

A wide window needs two shades moving together

Fabric rolls crooked and rubs one bracket

Old vinyl rollers snap back on their own

Our Process

How Lebanon Window Treatments Handles Roller Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Hardware inside the opening noted

2

Fascia or cassette settled

3

Written scope and total price

4

Brackets leveled, full travel run

5

Tube diameter sized to span

Real Project Photos

Roller Shades in Lebanon

Photographs from real roller shades jobs completed by our crew in Lebanon and surrounding areas.

Custom shades measured and installed in Lebanon
Scope of Work

What Roller Shades Includes

Every Lebanon job is documented item by item. Here is what the crew covers.

Roll direction decided at the measure, regular or reverse, and written onto the order in plain words

Cranks, locks and handles inside the opening noted, because a regular roll drops the fabric straight onto them

Fascia and reverse roll checked against the manufacturer's own rules, since Lutron doesn't offer that pairing

Three widths and three heights taken per opening, plus a corner-to-corner square check

Mounting depth measured for the tube and bracket, then measured again if a cassette or fascia is wanted

Tube diameter sized to the finished width and the fabric weight so a long roll doesn't sag mid-span

Fabric opacity settled in writing before ordering, light filtering against room darkening against blackout

Side channels and a light-blocking bottom pocket specified where a room has to go dark rather than dim

Light gap per side disclosed at the measure and repeated on the paperwork before the order goes in

Shades over 120 inches tall, or past a 4:1 height-to-width ratio, flagged for larger gaps up front

Factory deduction left with the manufacturer, which is typically 1/16 inch per side

Chain side set window by window so the control lands on the hand you'd naturally reach with

Chain tensioner fastened per the product instructions on every continuous cord loop shade

Cordless and motorized lifts priced where a hanging chain doesn't belong in the room

Hembar chosen against the fabric weight, exposed aluminum or wrapped in the shade fabric

Coupled shades drawn across wide openings so two tubes turn together on a single line

Bracket substrate confirmed ahead of install day so the right anchor or trim screw goes in

Every shade run full travel twice on install day to prove the fabric tracks centered without telescoping

Pricing

What Roller Shades Cost in Lebanon

National category numbers put stock shades near $60 to $600 a window and custom-fabricated shades roughly $250 to $2,600. Those are national ranges for the category and they aren't a quote for anything in Lebanon. Rollers spread across most of that band, because a roller is really a fabric decision wearing some hardware. A basic light filtering fabric on an open roll with a chain sits low. A blackout fabric in a cassette with side channels and a wrapped hembar sits far higher, and it should, since you're buying a light seal rather than a shade. Motorization is its own line, nationally $300 to $1,500 per window installed. Lebanon Window Treatments prices from measured openings across Boone County.

By Product

How Roller Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

Open roll: The tube and brackets left exposed above the window. It's the least expensive hardware and the most honest looking on a modern opening, though you do see the roll of fabric and the bracket ends from below and from the side.

Fascia: A flat aluminum face that runs across the front of the tube and hides the roll. It gives you a clean horizontal line above the window and it's usually wrapped or powder-coated. Note that reverse roll and fascia don't pair on Lutron systems.

Cassette headbox: A closed box around the tube, open only at the bottom where the fabric comes out. It hides the roll from every angle, keeps dust off the top of the roll, and gives a blackout install somewhere to tuck the top light gap.

Regular roll: Fabric comes off the back of the tube, so it hangs close to the glass. It's the default, it looks tidiest, and it's the roll direction that will foul a crank, a lock or a handle sitting inside the opening if nobody checked.

Reverse roll: Fabric comes off the front of the tube, standing off the glass by an inch or so. Specify it when there's hardware in the opening the fabric has to clear, or when a deep sill would otherwise catch the bottom of the shade.

Light filtering fabric: A woven or vinyl face that passes diffused daylight without a view through it. Rooms stay bright and glare goes soft. It's the everyday specification for a kitchen, a family room or anywhere darkness isn't what you're buying.

Room darkening fabric: A denser fabric that cuts most of the light coming through the face. Bedrooms are the obvious use. Understand that the face is doing the work and the edges are not, so an inside mount still passes light down both sides.

Blackout fabric with side channels: An opaque fabric run inside aluminum channels at each side so the edge light has nowhere to go. Paired with a cassette above and a pocket at the bottom, this is what actually makes a room dark rather than merely dim.

Continuous cord loop with a clutch: A bead chain running over a clutch in the end of the tube, which is the standard manual control. It handles weight well on tall shades. The tensioner has to be fastened to the wall or frame, not left hanging.

Dual bracket: One bracket carrying two tubes at the same window, so a solar screen and a blackout can live together and be used at different hours. It needs mounting depth, which is why we measure for it rather than deciding later.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a Lebanon room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Roller Shades FAQ

Questions we hear most often from Lebanon homeowners considering roller shades.

Enough to read by on a bright morning. Lutron publishes 3/4 inch per side as the inside mount light gap on Roller 20/64, plus a 1/16 inch per side factory deduction so the shade clears the opening at all. That's the physics of a fabric rolling on a tube inside a bracket, not a defect. In a family room it's invisible. In a bedroom on the west side of a Cedar Ridge house with no established canopy in front of it, it will wake you. That opening wants an outside mount, side channels, or both, and we'd rather price that at the measure.
It depends on what the opening puts in the way. A regular roll carries the fabric down the back of the tube, closest to the glass, which is what you want for light control. A reverse roll brings it down the front and clears obstructions, which is useful on the 1,275 pre-1940 houses here where a deep wood sill or a projecting stop would otherwise hold the fabric off the opening. The catch is that a reverse roll isn't compatible with a fascia, so if you want that flat closure across the front you're choosing a regular roll and solving the sill another way.
All three work on D.R. Horton's drywall returns, so it becomes a question of what you want to look at. An open roll shows the tube and the fabric wrap, which is the cheapest and the most honest about what it is. A fascia is a flat face across the front, which suits the plain trim in the $374,900 to $429,900 band those houses sell in. A cassette wraps the tube on more sides and closes off the top light path, which is the one that matters if the room is used for sleeping. We show samples of each rather than describing them.
Sometimes, and it's the most common measuring problem in this city. Lebanon has 1,699 houses from the 1970s, and the aluminum horizontal slider frames in them leave very little flat surface ahead of the operating track. A roller needs bracket depth, and a cassette needs more of it than an open roll does. We check mounting depth at the tightest point of each opening, not once per room. Where it's short, an outside mount on the trim gains you depth and closes both side light gaps at the same time, and on those houses it usually looks better anyway.
Tube diameter does the work, and past a certain width you need more of it. A long roller on an undersized tube deflects in the middle, the fabric tracks off center, and eventually one edge rubs the bracket. We size the tube to the finished width rather than to the price, which is why a wide shade costs more than two narrow ones covering the same glass. On a very wide opening, splitting into two shades under one head treatment is stronger, tracks straighter, and gives you the option of raising half the window.
You can order the fabric, but not the dye lot. Roller fabrics are run in batches and the color drifts between them, so a shade ordered twelve months later can read slightly different from its neighbors in the same nominal pattern, especially once the first set has taken a summer of light. If you know the plan, we order the whole run now and hold the extra shades boxed. If you don't, we record the fabric, the lot and the finished sizes so the second order is at least a known quantity.
Roll direction is simply which side of the tube the fabric comes off. On a regular roll it comes off the back and hangs close to the glass, which looks tidiest. On a reverse roll it comes off the front and stands off the glass by an inch or so. It matters because anything living inside the opening, a crank, a lock, a stop or a deep sill, will catch a regular roll. That's a decision made standing at the window with a tape, not afterward from a photo.
On Lutron systems that combination isn't offered, so we design around it rather than pretending otherwise. The reason is geometry: a fascia sits in front of the tube, and a reverse roll brings the fabric down that same front face, so the two want the same space. Other manufacturers handle it differently, and we check the specific line we're quoting instead of stating a universal rule. If you want the fascia look and the fabric needs to clear hardware, a cassette usually solves both.
Open roll is the least expensive and it looks right on a modern opening where exposed hardware isn't a problem. A fascia gives you a flat clean line across the front and hides the roll from below. A cassette wraps the tube on all sides, which hides the roll from every angle and gives a blackout install somewhere to hide the top light gap. Depth is what decides it in practice, since a cassette needs more mounting room than a bare bracket does.
Enough that you should hear the number before you buy. The shade has to be narrower than the opening to travel, so the factory takes its deduction, typically 1/16 inch per side, and light comes down each side of the fabric. Lutron publishes 3/4 inch per side as a real inside-mount figure on Roller 20 and 64. Shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps. If dark is the goal, an outside mount or side channels are the answer.
Room darkening describes the fabric. Blackout describes the whole install. A room darkening fabric blocks most of the light through its face and still passes light around every edge, which is why people call a bedroom dim and feel misled. A genuine blackout is an opaque fabric plus side channels, plus a cassette above and a pocket at the bottom, so the edges are closed too. We separate these in writing before ordering because the words get used loosely everywhere else.
Telescoping is fabric walking sideways on the tube as it rolls, so over a few cycles it creeps toward one end and starts rubbing a bracket. It usually comes from a tube that isn't level, a shade that was forced when it jammed, or fabric cut slightly off square. On a new install it's mostly prevented by mounting the brackets dead level and running the shade full travel twice before we leave. On an existing shade it can sometimes be corrected with shims at one bracket.
Wider than most people need, and the limit is deflection rather than fabric. As a shade gets wide, the tube has to carry its own weight plus the fabric across the span, and a tube that's too small for the width visibly dips in the middle. Manufacturers publish a tube diameter chart against width and fabric weight, and we work from that. Past the practical limit we couple two shades on one line so they turn together and read as a single treatment across the opening.
Chain is the standard and it handles weight best, which matters on a tall shade, but it means a loop hanging beside the window and a tensioner screwed to the wall. Cordless suits smaller shades and rooms where nothing should hang, though a very heavy shade fights a spring. Motors make sense on tall shades, on hard-to-reach windows and on a group you'd rather run together. Hunter Douglas states PowerView battery life is about a year, and batteries are the most under-disclosed cost on a motorized job.
Yes, and it's not a suggestion from us. The tensioner is the small device that anchors the bottom of a continuous cord loop so the chain stays taut against the wall or the frame instead of hanging as a free loop. It ships with the shade, the product instructions require it to be fastened, and a loose loop is exactly the hazard that the ANSI/WCMA A100.1-2022 work on cord access exists to address. We install it as part of the job rather than leaving it in the box.
Yes, on a dual bracket. One bracket carries two tubes at the same opening, so you can run a light filtering or solar fabric during the day and drop a room darkening or blackout shade at night. It's the honest answer when one fabric can't do both jobs, and it beats compromising on a single middle-of-the-road fabric that disappoints in both directions. It needs mounting depth, which is why we measure for the pair rather than adding one later.
Some fabrics curl slightly at the vertical edges over time, particularly lighter weight vinyls in a hot window, and it's a fabric property rather than a defect. Heavier woven fabrics and anything with a knit backing resist it. On the bottom, an exposed aluminum hembar hangs dead straight and is the practical choice on a wide shade, while a hembar wrapped in the fabric looks softer and is better on lighter fabrics. We match the hembar to the fabric weight rather than to a preference.
We can order the same fabric name if it's still in the line, and the color may not be identical. Fabrics run in dye lots, and a bolt woven this year can sit slightly off one woven two years ago, which nobody notices across a house and everybody notices on two windows in the same wall. The practical advice is the same as it is with paint: do a room at once. We write the fabric name and color onto your paperwork so a later order starts from the right reference.
Years, with honest caveats. Solar screen weaves and vinyl-faced fabrics hold up well against direct sun. Lighter decorative fabrics soften and lose color faster on a west or south window than the same fabric on a north one, and the exposed edge that sits outside the roll ages before the rest. Keeping the shade down through the worst afternoon hours actually protects the room behind it, which is the tradeoff. Fading in the room is reduced by the shade, not ended by it.
Two to five weeks is the normal custom fabrication window, with specialty fabrics and anything involving side channels or coupled tubes running toward the longer end. Motorized shades add a step because the tube gets built around the motor. None of that is a delay, it's a factory assembling to your measured sizes. You'll get the fabrication window in writing along with scope, dates and total price, which the Indiana Home Improvement Contract Act requires on residential work over $150.
Areas We Serve

Roller Shades Across Lebanon

We measure and install in every one of these Lebanon neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in Lebanon

Lebanon Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in Lebanon

Slats that ignore a Lebanon August

Learn more →

Wood Blinds in Lebanon

Basswood for the rooms with casing worth matching

Learn more →

Vertical Blinds in Lebanon

The honest answer to a wide patio door

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in Lebanon

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
Lebanon, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 863-9966
Service area

Serving Lebanon and the surrounding area

Call NowGet Quote